Toyota ECO15A Instruction Manual

SP10 Series• Read this manual carefully before use and always follow the instructions.• Keep the manual in a convenient place for easy reference.• If

10• How to use handwheelAlways turn the handwheel towards yourself. (in the direction of the arrow, forwards)Note: If you turn it in the reverse dire

11• How to use quick adviserThis quick adviser describes basic countermeasures about the main troubles.Meaning of the illustrationsIllustrations of th

12Prepare the foot controller.Insert the power cord connector into the terminal box.Insert the power plug into the outlet.The power is turned on.123•

13• Installation of battery for winding the lower thread31Pull the battery holder cover out as the arrow.2Install the battery while confi rming polari

14• Winding the lower threadUse a TOYOTA-exclusive bobbin.The exclusive motor driven by a battery winds the lower thread.13Pull the thread from the th

15674Pass the thread end through the hole of the bobbin as shown.Place the bobbin on to the thread winding spindle so the groove will meet the shaft p

164• Threading the lower threadCautionRemove the power plug from the outlet when setting the bobbin. Not doing so could cause an injury.1Take off the

17• Threading the upper threadCautionRemove the power plug from the outlet when threading the upper thread. Not doing so could cause an injury.1Turn h

186Pass the thread between the thread guide plate and the upper thread tension dial.7Pass the thread along the groove of the thread guide plate, as th

19• Pulling up the lower thread12Pull up the upper thread and the loop of the lower thread will come out.Pull out this lower thread.3Align the upper t

20• Application of each stitch patternButtonholeStraight stitch Sewing-seamsZipper insertionZigzagAppliqueOvercastingMending stitchThin fabric overcas

212• Changing the presser footCautionRemove the power plug from the outlet when changing the presser foot. Not doing so could cause an injury.Removal1

22Installation1Position the presser foot pin directly below the groove in the presser foot holder.2Lower the presser foot lever to secure the presser

232• Changing the needleCautionRemove the power plug from the outlet when changing the needle. Not doing so could cause an injury.Broken needles are d

24• Relationship between the needle, thread and fabric, and adjusting the thread tensionThe quality of the sewing fi nish will improve if the needle

25• Straight stitching and reverse sewingCautionStraight stitch132Position the fabric and lower the presser foot lever.Step on the foot controller to

26Thread cutter on the presser barLine up two threads and cut with the thread cutter on the presser bar.Reverse sewing is performed while pressing dow

27Sewing thick fabricWhen sewing thick fabric from the edge, the presser foot may tilt and be unable to feed through the fabric.Fabric or thick paperS

28Sewing tube-shaped fabrics1Pull out the extension table (accessory box) in the direction of the arrow.2Sew tube-shaped fabrics such as trousers or s

2912• Zigzag sewingThere are various zigzag applications, such as applique and overcasting.3Position the fabric and lower the presser foot.Step on the

Contents Before use• Important safety instructions ...4• How to change the power plug ...

30• Adjusting thread tensionUpper thread is tightWrongsideRightsideUpper thread is looseUpper thread is looseUpper thread is tightAdjustment method fo

31• Buttonhole sewingCautionRemove the power plug from the outlet when changing the presser foot. Not doing so could cause an injury.Buttonhole sewing

327456Raise the needle to the highest position, set the pattern dial to “4”, and sew 5 to 6 bar-tack stitches.Raise the needle to the highest position

338CautionUse the buttonhole cutter to cut the center, making sure not to cut the stitches.Note: If a marking pin is put in the bar-tack area it help

34• OvercastingThis is a sewing method that prevents unraveling at the edge of the fabric.1Zigzag sewing foot(Originally attached to the sewing machin

35• Zipper insertionCautionRemove the power plug from the outlet when changing the presser foot. Not doing so could cause an injury.784.0 2.0mm

364Sew until just before the presser foot makes contact with the slider, and then stop the sewing machine. 5Turn the handwheel towards yourself to lo

3753412• Blind hem stitchingIn this sewing method the stitch cannot be seen on the front of the fabric.Fold back the cloth so that the folded area pro

38Balanced stitchesSmall stitches evenly located on right side.Needle catches too muchon the foldLarge stitches on right side.Needle does not catch on

392• Feed dog and hook maintenanceIf the sewing machine makes a loud noise or rotates slowly, or there could be thread waste or dust in the hook or fe

4Do not operate where aerosol ( spray ) products are being used or where oxygen is being administered.Doing so could cause a fi re.Use an AC 220 to 240

403Attaching the Bobbin Case1Install the bobbin case from the front.The red mark a on the bobbin case should be in the position, as shown in the diagr

414• Changing light bulbWarningWhen changing the light bulb, disconnect the power plug and wait until the bulb cools. Not doing so could cause a burn

42• TroubleshootingWhat is the problem? Check the following possibilities before contacting the service center for repair.Trouble Cause Countermeasu

43If the above treatments do not solve the problem, contact the service center as described in your warranty.When calling for service, please note the

44Maintenance / OthersOthersIn a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means are provide

45OthersWe are committed to the protection of the environment. We strive to minimize the environmental impact of our products by continuously improvin

46• Specifi cations ModelSP10 seriesIf you have any queries about this TOYOTA sewing machine, check the warranty for details.Hook type HorizontalNeedle

679111-DBA10-D Web: www.home-sewing.com Head Offi ce Avenue de l’Industrie 21, Parc Industriel, 1420 Braine-L’Alle

5Do not repair, disassemble or modify except what is mentioned in the instruction manual.Doing so could cause an electric shock, a fi re or an injury.D

6• How to change the power plug When you change the power plug or cord, do not repair, disassemble or modify except at the authorised dealer or servic

7• Memo

8• Part names• External appearance may differ from model to model.Thread guideFace coverExtension table(Accessory Box)Upper thread tension dialSpool

9HandwheelThread winding switchTerminal boxThread winding spindleButtonhole adjustment screwPresser foot leverFoot controllerHollow for carryingBatter